Search  GO
Click to get connectedThe Listening Post Christchurch, The Listening Post (SI) LTD, The Listening Post Wellington, Sound EDid you Know? Top Banner
The Listening Post Christchurch | Browse by Brand |Anthem, MRX, 1120, AV, Receiver, MRX-1120, Amplifier, Home, TheatreThe Listening Post Christchurch | Browse by Brand |
  1. Home >
  2. Products >
  3. Amplifiers >
  4. Power Amplifiers >
  5. Stereo >
  6. Anthem M1 Monoblock Power Amplifier

Anthem M1 Monoblock Power Amplifier

Anthem MCA M1 Power Amplifier
New Product | The Listening Post Christchurch
Anthem M1 Monoblock Power AmplifierPurchase OnlinePrice per item: $6,499.00not currently available Enquire Now

Anthem M1 Monoblock Power Amplifier

 

Due December

 

The highest sound quality at all volume levels, flat frequency response into any load, and stable into the most difficult loads. The Statement M1 is a state-of-the-art monaural amplifier delivering 1,000 watts into 8 ohms and 2,000 watts into 4 ohms or less with THD remaining under 0.1% from 20 Hz to 20 kHz. Designed and engineered in Anthem's advanced research center in Ottawa, Canada, the M1 is manufactured in their Toronto facility.

 

More than just a slim, technologically advanced monaural design, the M1 demonstrates that Class D architecture isn't fundamentally flawed, it simply hasn't been implemented well in the past, mainly because it required such a heavy commitment to R&D. Anthem is fortunate to have the in-house resources to create such a groundbreaking product and one listen will reveal the truly extraordinary nature of this amplifier.

 

Features...

  • Full resolution of all of the sonic subtleties and complexities in the input signal.
  • Accurate reproduction of the full dynamic range of the signal.
  • Output stage is never allowed to clip.
  • No compression as output increases.
  • Flat frequency response into any load, without having to resort to digital conversion or equalisation to compensate.
  • Stable into all loads including open circuit and short circuit.
  • A low noise floor.
  • Exceptional efficiency with low heat output.
  • An amp so mechanically silent it will suit even the quietest listening room.
  • A design that allows multiple units to be stacked with no danger of overheating.
  • All of the above delivered at a price point that while not inexpensive, delivers virtually limitless dynamic fidelity.

 

Specifications...

  • Power Output continuous, 20 Hz to 20 kHz, <0.1% THD+N:
    • 8 Ω 1000 W
    • 4 Ω 2000 W
    • 3 Ω 2400 W
    • 2 Ω >2000 W depending on line voltage regulation
      • **With 120V AC supply the amplifier’s maximum output into impedances 4 Ω and lower, as well as its maximum duration, vary depending on line voltage regulation.
  • Frequency Response 20 Hz to 20 kHz:
  • Open circuit +/- 0.1 dB
    • 8 Ω +/- 0.1 dB
    • 4 Ω +/- 0.1 dB
    • 2 Ω +/- 0.2 dB
  • Power Bandwidth 1000 W at 8Ω: 5 Hz to 45 kHz
  • THD+N at 1 kHz, 8 Ω:
    • 1 W 0.01 %
    • 10 W 0.01 %
    • 100 W <0.03 %
    • 1000 W <0.06 %
  • S/N Ratio ref. 1000 W, IEC-A: 113 dB
  • Voltage Gain 29 dB
  • Input Sensitivity 100 mV for 1 W output, 3.2 V for 1000 W output (8 Ω)
  • Dimensions (H x W x D):
    • 1U rack mountable: yes
    • Or with feet/handles: 5.7 x 49 x 47.6 cm
  • Weight (unpacked): 9 kg

 

Best Value in the Market

The M1 enjoys all of the attributes of Anthem's award-winning Statement Class AB amplifiers but through exclusive Anthem technologies, goes far beyond the current capabilities of Class A, Class AB and prior Class D amplifiers in the market. The proprietary design employs all of the advantages of a Class D amplifier — high output, high efficiency, compact size — while avoiding the typical Class D limitations such as difficulty driving low-impedance (high-end) speakers, power line contamination, reliability issues and substandard audio quality. The absence of accurate dynamics is so common that it frequently goes unnoticed, but through the M1, music and movies are delivered with breathtaking realism.

 

Addressing the Class D bias

The “D” in Class D does not stand for digital. It was simply the fourth type of amp recognised and classified by the IEEE. The first was Class A, the second Class B, the third Class C, etc. Contrary to the bias that exists among high-end enthusiasts and across the industry in general, the Class D design is not inherently flawed. The truth is that no existing designs have been able to reach the Class D's inherent potential for performance. It is not the technology that yields fine audio performance but rather the implementation of the technology. At Anthem, they agree that most Class D amplifiers are poor performers. However the M1 uses Class D amplification of a different ilk (see later section on Class D for a full discussion).

 

The M1 is not a digital amp!

There are no A/D or D/A converters in the signal path. The amplifier’s control system continuously varies the width of the output pulse train in direct relation to the analog input signal. In essence, a side-to-side variation in width is analogous to a signal’s more familiar up-and-down amplitude variation, not at all the same as a digital string of 1s and 0s where all pulses have the same width.

 

Exceptional efficiency

Much has been written about Class D amps having twice the efficiency of conventional amplifiers at full output, but there's more to this. Under normal conditions an amplifier operates at only a fraction of its full output capability. At 1/8th of its maximum output (the typical working level of an amplifier), Anthem's M1 is six times more efficient than a conventional amplifier.

 

Never judge an amp by its size or its rack space

Amplifiers are often judged by their size and weight, the beefier the better since more power requires a physically heavier, larger amplifier. Or does it? It all depends on the design. When rack-mounted, the 20-kb M1 occupies only one rack space but despite its size can deliver 1,000W into 8 ohms and 2,000W into 4 ohms.

 

Cool running

The M1’s cooling system quickly and efficiently moves heat from the interior of the amplifier to exterior heat sinks. Sealed copper pipes within the amp contain a small amount of special fluid held under a vacuum. When the temperature at one end of the pipe rises — the end adjacent to the amplifier's heat sources — the fluid in that end evaporates. This vapor is then naturally drawn to the cooler end of the pipe, along the heat sink on the side of the amp’s chassis where it condenses. From there a copper wick returns the fluid to the hotter end of the pipe. This heat transfer process is many thousands of times faster and more efficient than cooling through metal heat sinks alone. This system eliminates the need for fans, allowing multiple M1s to be stacked with no danger of overheating. It also means the amplifier is so mechanically quiet it will suit even the quietest listening rooms.

 

You can find more information in the brochure - Anthem M1 Power Amplifier Brochure

 

    Related Products
    Christchurch Content Mangement Website